Product Details:
Payment & Shipping Terms:
|
| Material: | PE | Adhesive Side: | Single Sided |
|---|---|---|---|
| Adhesive: | Rubber, Butyl Rubber | Adhesive Type: | Pressure Sensitive |
| Design Printing: | No Printing | Color: | White,Gray,Yellow |
| Backing: | Polyethylene As Basic Material | Type: | Roll |
| Thickness: | 0.38 Mm To 1.0 Mm | Width: | 50 Mm To 800 Mm |
| Length: | 100,200,400,800 Ft | Application: | Corrosion Protection For Gas,oil And Water Pipeline |
| Standard: | DIN EN 12068 | Certificate: | ISO 9001,ISO 14001,ISO 18000 |
| High Light: | polyethylene tape,polyethylene sealing tape |
||
|
Description |
XUNDA T 200 series outer wrap tape is produced through extruding the composite anti corrosion materials. The adhesive layer is attached to the polyethylene film backing through thermal compounding. The anti corrosion system is comprised of primer, anti corrosion adhesive tape (inner tape) and protective tape (outer tape) The outer wrap tape always called Mechanical tape,outer tape,outer wrap tape, outer layer tape,outerwrap tape.The backing is more thicker with a few adhesive .The color is White.
|
||||||||||
|
Usage |
The XUNDA-T200 series is Cold applied tape coating system for corrosion protection of Oil, Gas, Petrochemical, and Waste Water underground or overhead pipelines. The outer-layer tape backing shall be compounded so that it will be resistance to outdoor weathering. It also provide protection to the inner layer from damage during storage, transportation, installation and throughout the lifetime of the pipeline
|
||||||||||
|
Features
& Benefits |
Featuring excellent insulativity Resistant to UV Easily applied with no special equipment Compatible with common pipe coatings Excellent resistance to cathodic disbonding Good Mechanical protective effect High mechanical strength Small water absorption Long service lifetime Good resistance to impact and ageing The outer wrap tape can be used in the construction conveniently with safety and no pollution The outer wrap tape is widely applied in many areas with high efficiency.
|
||||||||||
|
Material: |
High density polyethylene as backing layer and butyl rubber,synthetic resins as adhesive layer |
||||||||||
|
MOQ: |
100 rolls |
||||||||||
|
Package: |
2/4/6/8/12/24 rolls per carton |
||||||||||
|
Order Size |
|
||||||||||
|
TDS: XUNDA-T 265 = Polyken 955-25/Altene 122-25
|
|||||||||||
|
How to store the outer wrapping tape ? The coating materials shall be stored in a clean, dry area
All materials shall be delivered to the jobsite in sealed and labelled containers and shall be stored in a location that is protected from the elements, well ventilated and free from excessive heat, open flame, or other sources of ignition. Coating materials subject to freeze shall be stored in a heated area.
The materials storerooms shall be appropriately ventilated and shall comply with applicable law provisions on safety and fire prevention.
Tape stored at jobsites or material yards shall be kept dry and under cover and never exposed to direct sunlight. Rolls shall not be stacked more than four (4) tiers high and never directly on the ground or on irregular surfaces. The cores of stored tape rolls shall be vertical. Rolls shall not be thrown or dropped. Hooks or other sharp handling devices shall not be used. Tape shall not be stored in contact with protrusions capable of puncturing the material. Rolls or equipment shall not be piled on top of or against stored tape.
|
|||||||||||
|
How to install pipeline tapes? The inner-layer tape shall be applied directly onto the prepared pipe surface, Wrap tape application consists of hand application and machine application. The tape applied temperature must be above 5 degrees, the coating construction temperature shall be more than -5 degrees as better. The tape shall be spirally applied ,minimum overlap shall not be less than 50%.When applied to spirally welded pipe , the direction of the tape spiral shall be generally parallel to the weld spiral. The minimum overlap shall not be less than 25 mm. 4)When a new row of tape is started, the ends shall be overlapped at least 150 mm measured circumference.
|
|||||||||||
|
Project Pictures:
|
|||||||||||
|
Shipment Pic
|
|||||||||||
|
Jining Xunda Pipe Coating Materials Co.,Ltd
|
|||||||||||
|
Production Profile
|
|||||||||||
|
Quality Control:
|
|||||||||||
|
|
|||||||||||
Contact Person: Ms. Daisy Kong
Tel: 86-15265879789
Fax: 86-537-2599926
