Product Details:
Payment & Shipping Terms:
|
| Simliar Brand: | Polyken,,Altene | Film Layer: | Polyethylene |
|---|---|---|---|
| Adhesive Layer: | Butyl Rubber | Test Report: | SGS,DVGW,AWWA |
| Main Market: | Iran,UAE,Iraq,Kuwait,Turkey,Egypt,Libya,Ukraine,Russia,Uzbekistan,India, Australia,Indonesia,Kazakhstan,Ecuador,Venezuela,Bolivia,Argentina, Uruguay,Malaysia And So On. | Color: | Black,yellow |
| Standards: | ASTM D 1000, EN 12068 | Thickness: | 0.38 Mm，0.50 Mm,0.75 Mm，0.9 Mm,1.65 Mm |
| Lenght: | 122m | Guarantee: | 1 Year |
| High Light: | pipe wrap tape for underground,pipe protection tape |
||
EN 12068 Polyethylene Corrosion Resistant Tape / Yellow Pipe Wrapping Tape
piping tape polyethylene anticorrosive xunda
piping tape polyethylene anticorrosive is Cold applied tape coating system for corrosion protection of Oil, Gas, Petrochemical, and Waste Water underground or overhead pipelines.
Features:
This product has been made by a special processing of butyl rubber to P.E. Its durability is strong and electric corrosion can be prevented. The pipe can be semi-permanently preserved which has an excellent effect on its corrosion resistance. It has a permanent and continuous adhesion effect, this outstanding combination of butyl rubber adhesion and P.E, make good weather resistance, outstanding electric and chemical characteristics and good workability for ease in both manual and machine work.
Usage:
1) Anti-corrosion of water pipe, gas pipe, oil pipe, etc
2) Anti-corrosion of electric wire, voltage and communication cable
3) Anti-corrosion of pipe in chemical factories having severe moisture and corrosion
4) Anti-corrosion of various pipe lines
Application temperature : -34°C ~ 71°C
Service temperature : -34°C ~ 85°C
Sub-material:
Primer: Primer increases tape adhesiveness.
Physical Properties
|
Item |
T-150 |
T-165 |
T-180 |
|
Total thickness |
0.51 mm |
0.65 mm |
0.80 mm |
|
Polyethylene Film |
0.31 mm |
0.34 mm |
0.39 mm |
|
Synthetic Adhesive |
0.20 mm |
0.31 mm |
0.41 mm |
|
Elongation at Break |
³ 400% |
||
|
Tensile Strength |
55 N/cm |
60 N/cm |
63 N/cm |
|
Yield Strength |
35.5 N/cm |
42.3 N/cm |
45.5 N/cm |
|
Peel Adhesion to Primed Pipe |
25 N/cm |
30 N/cm |
33 N/cm |
|
Dielectric Strength |
35 KV/mm |
45.8 KV/mm |
48 KV/mm |
|
Cathodic Disbandment |
0.24 in radius 6.4 mm |
||
|
Volume Resistivity |
2.5 x 1012 ohm.m |
||
|
Water Vapor Transmission Rate |
£ 0.1gm/M2/24h |
||
|
Water Absorption Rate |
< 0.10% |
||
|
Recommended Application Temperature |
-5 to +600 C |
||
|
Max Serve Temperature |
-40 to + 850 C |
||
|
Color |
Black |
||
|
Available Roll Size (width x length) |
2" to 32" X 50’ to 800’ |
||
How to use?
1) Pipe surface processing
thoroughly clean the surface of the pipe by removing all foreign material.
Completely remove any sharp projections from the area of the weld.
Remove all rust and/or other impurities using a steel brush.
2) Apply primer
Before application, shake or mix primer thoroughly.
Because it is highly volatile, make sure it is securely sealed after use.
Because it contains inflammable solvents, use caution when working near any open flames.
To obtain best results, apply primer in a temperature range of 0°C~25°C and for storage a
Temperature of -20°C~35°C is best.
Proper volume of primer is 100g per 1m².
When primer is applied and PE anti-corrosive tape is used, it is recommended to apply the
tape within a short time after the primer is completely dry.
Size:
thickness: 0.3mm-2.0mm
width: 10mm--500mm
length:10m-500m
Contact Person: Ms. Daisy Kong
Tel: 86-15265879789
Fax: 86-537-2599926
